Home page Home page

Ilaris
canakinumab

Package leaflet: Information for the user


Ilaris 150 mg powder for solution for injection

canakinumab


Read all of this leaflet carefully before you start using this medicine because it contains important information for you.


Not included in the pack


image

Mixing Ilaris


    1. Remove the caps from the Ilaris and water vials.

      Do not touch the vial stoppers. Clean the stoppers with the alcohol swab.

    2. Open the wrappers containing the syringe and the transfer needle (the 50 mm needle) and attach the needle to the syringe.

    3. Carefully remove the cap from the transfer needle

      and set the cap aside. Pull the plunger all the way down to the 1.0 ml mark, filling the syringe with air. Insert the needle into the water vial through the centre of the rubber stopper.

    4. Gently push the plunger all the way down until air is in the vial.

image


  1. Turn the vial and syringe upside down and bring to eye level.

  2. Make sure the tip of the transfer needle is covered by the water and slowly pull the syringe plunger down to slightly past the 1.0 ml mark. If you see

  3. Make sure 1.0 ml of water is in the syringe, then take the needle out of the vial. (There will be water remaining in the vial.)

bubbles in the syringe, remove bubbles as instructed by your healthcare professional or pharmacist.

  1. Insert the transfer needle through the centre of the

  2. Carefully remove the transfer needle from the vial

stopper of the vial of Ilaris powder, taking care not to touch the needle or the stopper. Slowly inject the

water into the vial containing the Ilaris powder.

and recap the needle as instructed by your healthcare provider or pharmacist.

10. Without touching the rubber stopper, swirl (do not shake) the vial slowly at an angle of about

45 degrees for about 1 minute. Allow to stand for

5 minutes.

  1. Now, gently turn the vial upside down and back again ten times, again taking care not to touch the rubber stopper.

  2. Allow to stand for about 15 minutes at room temperature to get a clear to opalescent solution.

    Do not shake. Do not use if particles are present in the solution.

  3. Make sure all of the solution is in the bottom of the vial. If drops remain on the stopper, tap the side of the vial to remove them. The solution should be clear to opalescent and free of visible particles. The

solution should be colourless or may have a slight

brownish-yellow tint.

- If not used immediately after mixing, the solution should be stored in the refrigerator

(2°C to 8°C) and used within 24 hours.


image

image

Preparing the injection


  1. Clean the rubber stopper of the vial containing the

  2. Uncap the transfer needle again. Pull the plunger of the syringe all the way down to the 1.0 ml mark,

Ilaris solution with a new alcohol swab.

filling the syringe with air. Insert the syringe needle into the vial of Ilaris solution through the centre of the rubber stopper. The needle should not be in the liquid at this point. Gently push the plunger all the way down until all of the air is

injected into the vial. Do not inject air into the liquid.

16. Do not turn the vial and syringe upside down, the vial should stay upright. Insert the needle all the way into the vial until it reaches the bottom edge.

  1. Tip the vial to ensure that the required amount of solution can be drawn into the syringe

  2. NOTE: The required amount depends on the dose to be administered. Your healthcare provider will instruct you on the right amount for you.

  3. Slowly pull the syringe plunger up to the correct mark (amount to be given), filling the syringe with Ilaris solution. If there are air bubbles in the syringe, remove bubbles as instructed by your healthcare provider. Ensure that the correct amount of solution is in the syringe.

  4. Remove the syringe and needle from the vial. (There may be solution remaining in the vial.) Recap the transfer needle as instructed by your healthcare provider or pharmacist. Remove the transfer needle from the syringe. Place the transfer needle in the sharps container.

  5. Open the wrapper containing the injection needle and attach the needle to the syringe. Set the syringe aside.


image

image

Giving the injection



  1. Choose an injection site on the upper thigh,

  2. Clean the injection site with a new alcohol swab.

  3. Gently pinch the skin up at the injection site. Hold the syringe at a 90-degree angle and in a single,

abdomen, upper arm or buttocks. Do not use an area that has a rash or broken skin, or is bruised or lumpy. Do not inject into scar-tissue as this may mean you do not get all of your medicine. Avoid

injecting into a vein.

Allow the area to dry. Uncap the injection needle.

smooth motion, push the needle straight down completely into the skin.

image

25. Keep the needle all the way in the skin while slowly pushing the syringe plunger down until the barrel is empty. Release the pinched skin and pull the needle straight out. Dispose of the needle and syringe in the sharps container without recapping or removing the needle.

image

After the injection


26. Do not rub the injection area. If bleeding occurs,

apply a clean, dry cotton swab over the area, and press gently for 1 to 2 minutes, or until bleeding

stops. Then apply an adhesive plaster.

  1. Safely dispose of needles and syringe in the sharps container or as directed by your healthcare provider or pharmacist. Never re-use syringes or needles.

  2. Properly dispose of vials containing remaining water and Ilaris solution (if any) as directed by your healthcare provider or pharmacist. Any

unused product or waste material should be disposed of in accordance with local requirements.

Keep the sharps container out of reach of children. Dispose of it as directed by your healthcare provider or

pharmacist.