Home page Home page

Jetrea
ocriplasmin

Package leaflet: Information for the patient


JETREA 0.375 mg/0.3 mL solution for injection

Ocriplasmin


Read all of this leaflet carefully before you are given this medicine because it contains important information for you.


What Jetrea looks like and contents of the pack

Jetrea is a solution for injection in a vial. The solution is clear and colourless. Each pack contains one vial.


Marketing Authorisation Holder

Inceptua AB Gustavslundsv. 143 16751 Bromma Sweden


Manufacturer Oxurion NV Gaston Geenslaan 1 B-3001 Leuven Belgium

This leaflet was last revised in


---------------------------------------------------------------------------------------------------------------------------


The following information is intended for healthcare professionals only:


Jetrea must be administered by a qualified ophthalmologist experienced in intravitreal injections. The diagnosis of vitreomacular traction (VMT) should comprise of a complete clinical picture including patient history, clinical examination and investigation using currently accepted diagnostic tools, such as optical coherence tomography (OCT).


JETREA 0.375 mg/0.3 mL solution for injection is a ‘ready-diluted’ formulation, no further dilution is required. The recommended dose is 0.125 mg in 0.1 mL of the solution administered by intravitreal injection to the affected eye once as a single dose. Each vial should only be used once and for the treatment of a single eye. Treatment with Jetrea in the other eye is not recommended concurrently or within 7 days of the initial injection in order to monitor the post-injection course including the

potential for decreased vision in the injected eye. Repeated administration in the same eye is not recommended.


See section 4.4 of the Summary of Product Characteristics for instructions on post-injection monitoring.


Single use vial for intravitreal use only.


Preoperative antibiotic drops may be administered at the discretion of the treating ophthalmologist.


The intravitreal injection procedure should be carried out under controlled aseptic conditions, which include the use of surgical hand disinfection, sterile gloves, a sterile drape, a sterile eyelid speculum (or equivalent) and the availability of sterile paracentesis (if required). The periocular skin, eyelid and ocular surface should be disinfected and adequate anaesthesia and a broad spectrum topical microbiocide should be administered prior to the injection according to standard medical practice.


Only 0.1 mL of the total 0.3 mL solution in the vial should be administered. Any excess volume should be expelled prior to injection in order to deliver a single dose of 0.1 mL containing 0.125 mg ocriplasmin.


The injection needle should be inserted 3.5-4.0 mm posterior to the limbus aiming towards the centre of the vitreous cavity avoiding the horizontal meridian. The injection volume of 0.1 mL is then delivered into the mid-vitreous.


Instructions for use


  1. Remove the vial from the freezer and allow to thaw at room temperature (takes about 2 minutes).

  2. Once completely thawed, remove the protective blue polypropylene flip-off cap from the vial

    (Figure 1).

  3. Disinfect the top of the vial with an alcohol wipe (Figure 2).

  4. Visually inspect the vial for particulate matter. Only a clear, colourless solution without visible particles should be used.

  5. Using aseptic technique, withdraw all of the solution using an appropriate sterile needle (slightly incline the vial to ease withdrawal) (Figure 3) and discard the needle after withdrawal of the vial contents. Do not use this needle for the intravitreal injection.

  6. Replace the needle with an appropriate sterile needle, carefully expel the excess volume from the syringe by slowly depressing the plunger so that the plunger tip aligns with the 0.1 mL line on the syringe (corresponding to 0.125 mg ocriplasmin) (Figure 4).

  7. Inject 0.1 mL of the solution immediately into the mid-vitreous.

  8. Discard the vial and any unused portion of the solution after single use.


Any unused medicinal product or waste material should be disposed of in accordance with local requirements.


JETREA

0.375 mg/0.3 mL solution for injection


JETREA

0.375 mg/0.3 mL solution for injection


image


JETREA

0.375 mg/0.3 mL solution for injection


JETREA

0.375 mg/0.3 mL solution for injection


image

image

image

Figure 1 Figure 2 Figure 3 Figure 4


Information about storage


Do not use this medicine after the expiry date which is stated on the label and on the carton after EXP. The expiry date refers to the last day of that month.

Store in a freezer (-20 °C ± 5 °C). After thawing

The unopened vial in the original carton protected from light may be stored in a refrigerator

(2 °C to 8 °C) for up to 1 week. The new in-use expiry date should be calculated and noted on the carton before it is placed in the refrigerator.


Once removed from the freezer or refrigerator, the medicinal product may be kept below 25 °C for up to 8 hours. At the end of this period the product must be used or discarded.

Do not refreeze a vial once it has been thawed. After opening

From a microbiological point of view, the medicinal product must be used immediately after opening. The vial and any unused portion of the solution must be discarded after single use.